Propellerhead Reason - 4.0 Instrukcja Operacji Pobierz pdf (Strona 359)

THE EFFECT DEVICES

357

PH-90 Phaser

The PH-90 Phaser is a classic phaser effect with some special features for fine-tuning

the sound. It can create the classic sweeping phaser sounds suitable for pads or gui-

tars, but also more extreme effects if you like. The phaser is best used as an insert ef-

fect.

Theory

A phaser works by shifting portions of the audio signal out of phase, and then adding

the processed signal back to the original one. This way, narrow bands of the fre-

quency range (“notches”) are filtered out. When these frequencies are adjusted, a

sweeping phaser sound is created.

The PH-90 is a four-stage phaser, which means that there are four “notches” in the

frequency response curve (this is a little like using four notch filters with different filter

frequencies - see page 192 for an explanation of notch filters).

When the phaser frequency is adjusted (manually or by the built-in LFO), these

notches will move in parallel in the frequency spectrum. Furthermore, you can adjust

the distance between the notches (Split) and their Width. Adding feedback raises the

filter gain just below each notch in the frequency range, creating a more pronounced

effect.

Parameters

CV Inputs

The following CV inputs are available on the back panel of the device:

D Freq CV.

Adjusts the frequency parameter. Use this e.g. for creating envelope controlled

phasing (preferably with LFO Freq. Mod turned off in the device).

D Rate CV.

Lets you control the speed of the modulating LFO from another device.

About Stereo and Mono connections

The PH-90 can be connected using mono or stereo inputs, as shown by the graphs

on the back panel. Note the following:

D A “moving” stereo effect is only obtained when you use a mono input

and stereo outputs.

With a stereo input, the two sides are processed in parallel, maintaining the stereo

image of the original sound.

D When you are using a mono input and stereo outputs, there will only be a

stereo effect if the internal LFO is used.

If you turn LFO Mod Amount to zero, both stereo outputs will carry the same signal

(mono). This is because the “fake stereo” effect is produced by inverting the mod-

ulation for one of the output channels.

Parameter

Description

Frequency Sets the frequency of the first notch. Adjusting this will move the

other notches correspondingly. This is the parameter modulated by

the LFO to create phaser sweeps.

Split This adjusts the distance between the notches in the frequency

range, thereby changing the character of the effect.

Width Determines the width of the notches. Raising the Width deepens

the effect and simultaneously makes the sound more hollow and

thin. This will also have an effect on character of the feedback

“tone”.

LFO Rate This is the speed of the LFO modulating the frequency parameter.

The higher the value, the faster the phaser sweeps.

LFO Sync This button lets you activate/deactivate LFO sync. When it is acti-

vated, the frequency of the LFO is synchronized to the song tempo,

in one of 16 possible time divisions. The LFO Rate knob is then

used for setting the desired time division. Turn the knob and observe

the tooltip that appears for an indication of the time division.

LFO Freq. Mod This determines the depth of the LFO modulation, i.e. by how much

the frequency parameter should be modulated.

If you turn this to zero, the effect will be a static, formant-like sound

(most effective if you add a little feedback).

Feedback This is similar to the resonance control on a filter. Raising the feed-

back gives a more pronounced “tone” in the effect. For “singing”

phaser sounds, try raising this to the maximum.

Parameter

Description

1 2 ... 354 355 356 357 358 359 360 361 362 363 364 ... 401 402

Komentarze do niniejszej Instrukcji

Brak uwag

Propellerhead Reason - 4.0 Instrukcja Operacji Strona 359

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Oprogramowanie Propellerhead Reason - 4.0